How to Make A Corset
If you want to learn how to make a corset - a real corset -
Foundations Revealed™ is going to rock your world.
Whether you're an enthusiastic amateur or a seasoned pro, this site will bring you all the corset making instruction you've always wished you could find on the Internet, but that no-one was willing to reveal.
Let us encourage you to have a go - the very best way to learn how to make a corset is to jump in and do it!
Introduction
In this article we are going to look at a simple method for how to make a corset, one that is ideal for beginners. By following the steps you will learn about some of the key principles of a corset.
(For subscribers and those interested in greater detail, this corset is also presented as a two-part article which goes into greater detail. Part 1 and Part 2 are best read following The Six Rules of Good Corsetry: a basic guide.)
Figure 1: Beautiful stitching just takes a little practice
Keep it simple
Following a small set of basic rules can be a very worthwhile approach for corsetieres both new and old, and here's number one: Simplicity is good. Simplicity of cut and construction can be inspirational, in fact. It is worth noting to new makers that the more you have going on in the corset (figure 2), the more there is to potentially go wrong!
The challenges of more complex corsets can, I fear, put many people off very early in their corsetry studies. By beginning with simple construction, you'll hopefully feel rewarded and encouraged enough to continue past your first few efforts.
Figure 2: A Sparklewren midbust. It looks rather simple, but the processes required are actually quite involved.
Patterning and Fitting
In this article, I will be focussing on construction rather than patterning. I will be using one of my own old prototype corset patterns (right), and I'd recommend that you look to the following sources for good beginner's corset patterns:
- For those who want to learn more about how a flat pattern becomes a 3D garment, I suggest following our free Beginners' Drafting Tutorial. You will learn a lot following this process, but it is clear/simple enough to follow, even for absolute beginners.
- For those who find flat patterns or mathematical alterations daunting, I would suggest using the Truly Victorian 110 pattern, with a toile or two. I have seen beautiful results with this pattern, even in the given “standard” sizes, and in my opinion it is the most prettily shaped of the commercially available multi-size patterns (caveat: I haven't tried this pattern myself, so can't comment on the enclosed instructions, etc.)
- For those who have a few pennies to spare and really want to get straight to the fitting stage, it may be possible to find a corsetmaker who produces custom/bespoke patterns to order. Try searching the livejournal corsetry community or etsy. But please do your research before making a purchase.
Let's Begin
This corset is about simplicity. With that in mind, it will have a closed front and pared down construction, and is loosely based upon my spot broche coutil corset dresses (below).
I have explored corset dresses in both ornate (figure 4) and simple (figure 5) styles, but each idea has been built around the functional beauty of spot broche coutil fabric. This incredible fabric, especially designed for making corsets with, is thick and heavy without being difficult to handle or sew. Readily available in white, mid-grey, black, butterscotch, mid-nude and so on, it can also be dyed easily.
Figure 4: An ornate spot broche coutil corset-dress in white. 
Figure 5: A simple spot broche coutil corset-dress in grey.
Broche is beautiful to work with because:
- It wears beautifully, is perfect for foundation wear, and is a dream to press and sew.
- It is simple and clear to find, and straighten, the grain.
- Cutting broche is very easy.
Whilst many new students ignore broche on account of its price tag, it is in fact one of the best and easiest corsetry fabrics to learn on. I firmly believe that one toile made with a proper corsetry-appropriate fabric is worth twenty made with fabrics that are not, in terms of how quickly you will learn and how happy you will be with the corsets you make (even if only for yourself for parties here and there!). The ease with which you can great results with broche make it actually a rather cost-effective way to learn in the long run and I would actively encourage people to buy and try broche so that we may assist in keeping these mills and machines running.
Using spot broche coutil allows us to focus on simplicity of construction. But even with this simplicity in mind, it is possible to have a bit of fun with design... Figure 6 shows a couple of quick scribblings I did when imagining this corset - as you can see, simplicity does not have to be dull or repetitive.
Figure 6: Violet spot broche corset ideas.
Preparation
MATERIALS:
- 1.5m spot broche coutil in white (which I dyed using Dylon's machine dye in “Intense Violet”).
- Flat and spiral steel (I cut my steel from the roll, but you can also measure your channels and purchase appropriate lengths).
- All-purpose thread.
- Two-part Prym eyelets (I'm using chrome).
EQUIPMENT:
- Straight-stitch sewing machine.
- Tailor's awl or fabric/leather punch.
- Bias binding makers.
- Water-soluble dressmaking tape.
I dyed my broche, but if you are using an existing colour then all you need to do is steam press to shrink it slightly. This will keep the fabric's finish crisp and firm. Please note: if you intend to wet wash your corset in the future (which isn't usually advised) then you will want to pre-shrink your broche in the machine first.
Figure 7: White broche, “intense violet” Dylon machine dye, and violet thread.
Construction: First Steps
Cut the CB (centre-back) pieces twice, on the fold, with no seam allowance at the back. In other words, put the fold of the fabric on the stitching line at the centre back, not the edge of the pattern piece. This will save you from having to make a neat finish at the back edges, since the fold *is* the back edge. Figure 9 shows this CB fold more clearly as it goes through the sewing machine.
Cut the CF (centre-front) piece once on the fold, also with no seam allowance at the front. Then cut each of the other pieces twice, keeping the waist-line on the cross-grain. (The cross grain goes across the fabric, at right angles to the selvedge, or woven edge of the fabric.)
Figure 8: the cut broche.
Once cut, I like to prepare the CB panels first.
Stitch a series of lines to create a boning channel, eyelet/grommet channel, and a final boning channel (figure 9). Either mark these out in advance, or use the edge of the presser-foot and/or gauge on your sewing machine to create nice straight lines.You need to make these channels as wide as is suitable for your preferred width/thickness of flat steel bones. Stitch a couple of test channels first on a scrap piece and make sure your flat steel runs through them smoothly but snugly.
Figure 9: Stitching channels down the CB panel.
Construction: The Seams
Now we are ready to begin stitching the seams, with the wrong sides together.
You may pin or baste your pieces together before stitching each seam, but if your seams are trued (ie they match properly, as a commercial pattern should) it can be possible to simply match up the top edges and guide the seams through the machine without securing first. Figure 10 shows the CF panel and right-hand panel 2 being stitched.
Figure 10: Stitching the first seam.
As I go along, each seam is pressed open (figure 11). The seams are stitched with the fabric edges to the outside (ie: wrong sides together) as the seam allowances are going to be covered by exterior bone casings. Seams that are pressed open are a bit of a hot topic in corsetry, but for a piece that cinches only gently, they work fine (and I have also seen them work brilliantly on tight-lacing corsets).
Figure 11: The seams are pressed open, either as you go along or once they are all stitched.
Stitch all remaining seams in the same manner. Figure 12 shows the corset from the inside with all of the seams stitched except the right-hand CB panel. You can see the waist-tape (currently unattached) running into the left-hand CB seam. This allows for a tidy finish to the interior of the corset.
Figure 12: All seams but one stitched, showing the placement of the waist-tape.
At this stage I like to stitch the seam allowances down (figure 13), catching the waist tape as I go.
Figure 13: Stitching the seam allowances open and anchoring the waist-tape simultaneously.
Once the waist-tape is anchored at each seam, you can stitch the final CB panel in place. Simply catch the waist-tape between the layers as you stitch the seam (figure 14), press it open, and stitch the allowances down as previously (figure 15). Figure 16 shows the interior at this stage.
Figure 14: Catching the waist-tape in the seams of the final panels.
Figure 15: Stitching the final seam open.
Figure 16: Seams stitched open and waist-tape anchored in place.
Measure the waist to check the size, and when you're sure it's right, trim the seam allowances down (Fig 17).
Figure 17: Trimming the seam allowances using my beloved “duckbill” applique scissors.
Exterior casings
We have stitched our seams to the outside and now we need to create and attach casings for the bones to slip into.
Firstly, I cut a couple of strips of broche out of my leftovers "on the bias" (ie diagonally to the edges of the fabric).
Cut a couple of strips of your broche on the bias and a few on the straight-grain (parallel to the fabric edges). The bias strips create casings that can be pressed into nice curving lines, which is useful if you're adding decorative casings. The straight-grain strips will become your vertical casings (those which contain the steels).
Figure 18: Bias strips of broche coutil.
After pressing using a bias-maker, the strip has crisp edges and is ready for stitching (figure 19 shows the inside of such a strip). I find that thicker fabrics like broche often need to be cut slightly narrower than the bias-maker suggests.
Figure 19: Inside of the broche strip/casing.
With the casings ready, you can decide upon placement of the decorative bias casings and stitch them down along each edge.
Figure 20: The decorative bias casings stitched in place.
I then stitched down the CF casing and checked the layout of my remaining vertical casings (figure 21).
Figure 21: Checking the layout of the casings.
Each remaining vertical casing is stitched down at the edges and once through the centre (figure 22). When choosing width for your casings, make sure there will be enough room for your preferred steels. In my experience, broche exterior casings need an extra mm or two space more than sandwiched channels.
Figure 22: Stitching the vertical casings down.
Continue until your casings are complete!
Figure 23: Completed exterior casings.
Binding, Bones and Eyelets
The easiest choice for beginners is to use a pre-made bias binding to finish the corset. Satin, cotton, faux leather, etc. can all create different effects, and for this corset I decided to use black faux leather. We're going to bind the bottom edge, put the steel bones in, and then finish off by binding the top edge.
The quickest way to bind a corset is by machine. First we need to sort out those ends. Leather and faux leather do not recover from stitching, so we cannot baste or pin our binding in place. Instead, we can tape it. Figure 24 shows a small bit of clear water-soluble dressmaking tape placed at the bottom outer corner of one of the CB panels.
Figure 24: Clear dressmaking tape
The faux leather binding is pressed onto the tape and folded and taped to the inside (figure 25).
Figure 25: Sticking and folding the binding in place.
The binding is then folded and taped (figure 26) to hold it temporarily in place. Alternatively, you may trim the binding edges rather than fold them away (leather and faux leather won't fray). At this stage, you can either tape the entire length of the binding, or you can start stitching folding the binding around the lower edge of the corset by hand as you go (figure 27). You can also purchase feet designed to make this process easier, but I wished to challenge my machine-finishing skills as they aren't as strong as my hand-finishing.
Figure 26: Folding the bias under. 
Figure 27: Stitching the binding in place.
Continue around the corset, folding and taping the final edge under in the same way that you started off. Secure your stitching.
Figure 28: The completed lower binding.
Cut, tip and insert your steel bones in the channels as required. Preparing steels is really simple, but for beginners it can be a good idea to buy in a range of lengths of spiral and flat steel which you can use over and over again in toiles and your first few experiments. I used spirals throughout (with flats at CB and CF) to give a corset that will mould into its desired shape quickly and smoothly. As the broche holds such a sturdy shape, only a minimum of steels are needed. Once your steels are in place, you may apply the top binding following your chosen technique.
Your two-part eyelets/grommets can be inserted following the directions on the pack. If you are widening your holes rather than punching them, it really is worth buying a tailor's awl as soon as possible. It makes the job so much easier and neater. When I first began learning, I used all sorts of implements which I had read could work as alternatives, sometimes resulting in injury to my hands (once a cut that produced so much blood I fainted!). Life is just easier if you get the appropriate tools.
Within the UK and Europe I can certainly recommend small packs of Prym 5mm two-part eyelets. Use a rubber mallet when hammering the eyelets in place, placing them 2cm (¾") apart down the length of the CB except at the waist, where 4 pairs can be spaced more closely together (1.5cm) to help disperse the extra strain found at the waist (figure 30).
Finally, you may lace your corset! I have here used “shoelace” style lacing with “bunny ears” at the waist. When trying your corset on for the first few times, lace up slowly to prevent any excessive strain or potential damage to your corset.
Conclusion
Figure 29: The final corset, front. 
Figure 30: The final corset, back
Ultimately, corset construction does not have to be excessively complex. As you progress with your corset-making studies you may find that your focus becomes one of complexity or of simplicity. Perhaps you will endeavour to develop swift and simple processes that result in exceptionally strong, lightweight, beautiful corsets. Or perhaps you will become enthralled with the difficulty of the numerous processes required in certain construction styles...
Either way, by beginning with a swift and clean construction method, I hope you will kick-start your studies. After all, the best way to assess fit and shaping is to make numerous corsets and toiles, for lacing onto your friends/models/self. Having a reliable and quick construction method can really speed up and enhance that process. Don't wait around, hoping to make a perfect corset first time... Even those of us who've made hundreds still have the odd failed or unsatisfactory attempt. It's best just to get working and experimenting as soon as inspiration hits you!
A few more examples of our specialised beginners' articles:
Step By Step Worksheets
|
Perfect Boning Channels
|
The Corset Maker's Tools
|
Draft your own Corset Pattern
|
Silverado Corset, Start to Finish
|
Basic Flexible Busk Insertion
|
Laura shares with us her step by step corset construction worksheets for making a 2-layer corset with and without a waist tape.
Lots of people have asked how to get perfectly straight and even boning channels. Here are a few tips and tricks that'll help you tame unruly stitching.
What are the correct tools for corsetry, when some swear by tools that others avoid? Pro Laura Loft shares what's in her toolbox.
How to make your own personalised custom Victorian corset pattern from your own measurements - suitable for beginners!
Laura Loft takes a popular commercial pattern and shows you every last detail, step by step, from beginning to end of constructing a professional quality corset.
A tricky skill to master: a few techniques on how to handle and insert the hook and eye busk at the front of the corset without tears - and how to keep your stitching straight.Hit the menu tab above marked "Beginner" to see our full range of articles that are specially designed to get you started right. Meanwhile, under our other menu tabs you'll find corsetmaking articles that run right through from beginner, to intermediate, to professional level, pushing the boundaries of modern corsetmaking, working out how complex Victorian corset patents worked and giving you advice on running your own corsetry business.
All you need is a Paypal account, meaning that you have complete control - you can cancel any time through your own Paypal. (This keeps us on our toes producing features that offer the very best and clearest how-tos, ensuring that your work becomes the very best and that you stick around for more!) We make sure that we're giving you what you need with regular surveys and polls, so whether your sticking point is fitting plus sizes, drafting, getting boning channels around curves smoothly, or whether you want patterns from real Victorian corsets and flossing (corset embroidery) ideas directly from the past, we can give you what you need.
For you, this means that you become more confident, your drafting, fitting, sewing and finishing start to fly headlong towards the finest professional standards, and you get to realise your corsetmaking dreams with the closest thing that the 21st century can offer to a true apprenticeship from Victorian masters. All this for a lot less than the average college course, and your first month is half price!
By re-kindling the culture of apprenticeship in a modern, technological age, we can return to a world in which true craftsmanship is once again loved, appreciated and shared successfully for the greatest advantage to everyone.
If you're into corsetmaking and you know anything at all about our award-winning sister site on historical clothing, Your Wardrobe Unlock'd™, you'll know all about how we work. Come with us, and enter a world in which truly outstanding work is not only possible, but achievable...
Click here to become a member of Foundations Revealed™ now!
Subscribe 
RSS
Interested in making my first custom corset
would like to know more about corcet making
I love reading these articles! I always learn something new! Thank you again!
Hello :)
I stumbled upon your website and am very interested in your course but would like to know how long does it take to achieve middle level (I'm still on a budget at the moment). SO I can plan better and not pass on any goodies I can get from here.
Thanks in advance for your reply.
Hi Interested, this website does not offer formal education or set courses at present, but is organised in a magazine format, with a new tutorial like this one available to paying members each week. When you sign up, you will have access to everything we have ever published in the last three years, since our launch.
The time taken to achieve "middle level", not to mention the definition of middle level, varies from person to person. Corsetmaking is still a very new field, and is as yet unregulated.
The article "Perfect Boning Channels" comes up with a Error 500 message.
